BenQ VAD6038 (62430c and 64930c)
To start of with you will need to download jungleflasher. This Utilitie will allow you to flash all drives pre to the slim. The slim firmware has not yet been relesed as of yet.
Next you will ned the firmware pack.
http://hotfile.com/dl/106393480/2a33650/JungleFlasher.0.1.79.Beta%28208%29.rar.htmlhttp://www.megaupload.com/?d=ORKGK4HHWhat is AP 2.5?
Anti-Piracy version 2.5 is the newest addition by Microsoft to detect custom DVD Drive firmware and is included in the new Kinect dashboard. This check has been included for some time but hasn't been activated until Kinect. This authentication blocks backups from being loaded and displays a message that states " This disc is unreadable."
If you get this message and you will be flagged to be banned.
Your drive needs to be conected to your pc via sata port and in the main port.The drive also needs to be have power. You can use a conectivity kit or power via the xbox 360 itself.
Now we have junglflasher and the firmware pack lets get started.
First we need to put our firmware pack into the jungleflasher app. We do this by unraring the firmware to desktop, rename from "iXtreme-LT_Plus_Firmware_Pack" to "Firmware" and placing in the jungleflasher folder like below. Just makes things more simple.
Now we need to run jungleflasher we must run jungleflasher as admin or it will not install the port I0 drivers. You should get this message.
Then click ok and you will see the application open.
The next steps are
Unlocking the Drive
Reading the Original firmware
Patching Key into hacked Firmware
Erasing Drive
Writing Drive
Now we need to set the drive to vendor mode. This allows us to read, write erase ect.
Eject the drive and then power of the xbox360 via the power cord. Push the dvd tray halfway in and power back on. Most cases you will have to hold the tray so it does not retun into the xbox. Its kinda tricky first time round but acomplishable on your own. This may take a try or two but its not hard.
Now click on the MTKFlash32 Tab, select you port I0 port and your drive will be shown and display in the drive properties as "Drive in vendor mode" and in the flash properties "Type serial flash with status 0x73
Next we need to reads the drives firmware. To do this we click "Read". Make sure you save this as if any of the next steps go wrong you will ned this to flash back to the drive. If you do not save this you will brick your drive and render your xbox 360 as a dvd player.
Once clicked save it should auto ask to to auto load iXtreme Click Yes. This will load to the source buffer.
Now click "firmware32" tab and check the dvd keys match in the source firmware and the target firmware. If they do not match click the spoof source to taget button in the middle of the screen. When they match proceed to the next step of writing the drive.
Make sure you still have good flash chip properties by clicking back on the "MTKFlash32" tab and look in the flash chip properties. We need 0x73 flash status.
If you have this click "Write". Once the write has finshed we should see "Write Verified Ok"
Now send an Outro to the drive by clicking "Outro/ATA Reset" this will relese the drive from vendor mode.
Power off – connect back to console and test with a backup game you have.
Compatable chipsets for flashing xbox 360 drives. If you do not have one of the following you will need to purchase one or get a VIA 624 chipset they are the cheapest.
-NVIDIA nForce 2 IDE Controller
- NVIDIA nForce 4 IDE Controller
- Intel P45 (ICH10R) ASUS P5QC
- Intel ICH9
- Intel ICH (i810,i815,i840)
- Intel ICH0
- Intel ICH2M
- Intel ICH2 (i810E2,i845,850,860)
- Intel C-ICH (i810E2)
- Intel ICH3M
- Intel ICH3 (E7500/1)
- Intel ICH4 (i845GV,i845E,i852,i855)
- Intel ICH5
- Intel ICH10
- Intel ICH10R (Asus P6T V2 Deluxe)
- Intel ICH10R+P45
- Intel ESB (855GME/875P + 6300ESB)
- Intel ICH6 (and 6) (i915)
- Intel ICH7/7-R (i945, i975,945P with silicon 3231 sata controller)
- Intel ICH9R
- Intel PIIX3 for the 430HX etc
- Intel PIIX4
- Intel PIIX4 for the 430TX/440BX/MX chipset
- Intel PIIX
- Intel 82801EB (ICH5)
- Intel 6300ESB (ICH5)
- Intel 82801FB/FW (ICH6/ICH6W)
- Intel 82801FR/FRW (ICH6R/ICH6RW)
- Intel 82801FBM ICH6M
- Intel Enterprise Southbridge 2 (631xESB/632xESB)
- Intel 82801GB/GR/GH (ICH7, identical to ICH6)
- Intel 2801GBM/GHM (ICH7M, identical to ICH6M)
- Intel SATA Controller IDE (ICH8)
- Intel Mobile SATA Controller IDE (ICH8M)
- Intel SATA Controller IDE (ICH9)
- Intel SATA Controller IDE (ICH9M)
- NVIDIA nForce 4 SATA Controller
- NVIDIA nForce 2 SATA Controller
- NVIDIA nForce 3 SATA Controller
- NVIDIA nForce MCP04 SATA Controller
- NVIDIA nForce MCP51 SATA Controller
- NVIDIA nForce MCP55 SATA Controller
- NVIDIA nForce MCP61 SATA Controller
- NVIDIA 750i
- NVIDIA Nforce630i (flashed a benq and lite-on)
- NVIDIA Nforce570 (Samsung M28)
- Silicon Image SIL-3512
- ATI SB600 (configured to legacy IDE)
Credits to Jungleflasher for some of the images images.
Credits to C4Eva for the public relese of the firmware.
I made this tutorial through my own kwnolage of flashing the benque drive. If you need more documentation look in the folder "Documentation" in the jungleflasher folder and there is a P.D.F there. This tutorial was ment to be a small understaning of what you need to do and how i do it.
*Imprortant Notice* If you ever get a black screen when attempting to play a backup game, this is the A.P 2.5 challenge you have 3 mins to power of the console. You need to disconect the power lead. You have 3 mins to do this or you will be flagged.
